- Public Sector
RubberForm Speed Table
Product Description
Our RubberForm Speed Tables are effective permanent or temporary traffic calming devices. Gentler than either speed bumps or speed humps, our speed tables calm traffic without loud disruption or risk of vehicle damage. They are fully modular and can span any width of road needed.
Our 100% American recycled composite material won’t crack, crumble, spall, or corrode in the searing heat, frigid cold, or any rain, ice, or snow common to North American roads.
Specifications:
- All Speed Tables are custom fit for your specific needs
- Modular design for custom widths and lengths
- Modules connect with a proprietary dual flange connector
- Available with all black or up to as many white or yellow arrowheads as needed
- Versatile arrow configurations to MUCTD specifications
- Made in the USA with 100% American recycled composite material
Product Description
Most traffic calming methods are massively inconvenient. They’re a huge pain to install and somehow worse to demolish and remove later. They’re loud, not always sized right, they can damage vehicles as they cross, and whether concrete or asphalt, they tend to chip, warp, and spall over time until they’re useless for calming traffic and ugly to boot.
Our RubberForm Speed Tables are carefully innovated to solve these problems. They’re blessedly simple to install: no large crews, no heavy equipment, no road closures. They’re gentler than speed bumps and won’t damage vehicles as they cross. In fact, speed tables are often used as crossings for pedestrians when the sidewalk can connect.
Our 100% American sourced recycled composite material can stand up to all the harshest conditions of American roads without chipping, warping, or spalling. It will last decades, even in the searing heat of the summer sun, the frigid cold of North American winters, or all the rain, ice, and snow you can throw at it.
Models
RF-SCLC
- Speed cushion left corner
- 18 lbs
- 3”H x 15-1/4”W x 40”L
RF-SCRC
- Speed cushion right corner
- 18 lbs
- 3”H x 15-1/4”W x 40”L
RF-SCRP
- Speed cushion ramp – no arrow
- 26 lbs
- 3”H x 16”W x 40”L
RF-SCRPA
- Speed cushion ramp with Thermoplastic White of Yellow arrow
- 26 lbs
- 3”H x 16”W x 40”L
Key Features
- Easy to install, remove, and relocate
- Proprietary Injection molded (duplicate/globally this wherever we say, Injection Molded).
- Modular design for custom widths or lengths
- Versatile arrow configurations
- Can be straddled by emergency vehicles
- Only speed cushion manufactured in the USA
- Made with 100% American recycled composite material
Hardware Kits
RF-SCHWK10
- 10 piece Speed Cushion Hardware Kit
- 40 – Lag Bolts: 10mm x 120mm
- 40 – Washers
- 40 – Anchors
- 40 – Black Caps
- 24 – Dual Flange Connector
RF-SCRT
- 2 Part Mortar Cement
RF-SCRDG
- Mortar Dispensing Gun
FROM ONE SPECIALIST TO ANOTHER
Related products
Whether you need speed bumps, roofing support, curb ramps, or more, RubberForm specializes in safety and risk mitigation.
FREQUENTLY ASKED
Are your speed cushions and speed tables truly made in the USA?
What is the turnaround time for your speed cushions and speed tables?
What material are your speed cushions and speed tables made of?
Can we remove your speed cushions and speed tables for the winter when our snowplows are on the roads?
What reflective material do you use on your speed cushions and tables?
What is the difference between a speed cushion and speed table?
A speed cushion is narrow enough to allow emergency vehicles to pass unimpeded. A speed table is made from the same section pieces, but spans the whole street. Both are effective traffic calming devices.
How are your speed cushions and speed tables anchored down?
We offer a lag bolt anchor mounting system consisting of a lag bolt, plastic lag shield, and washer to anchor into pavement or concrete. There are 4 anchor holes for each modular section. We also include a two-part mortar cement that goes into the holes. This helps anchor the cushion or table on high traffic roads.
